Fire Alarm Systems

Model 1151eis ionization smoke detector uses a state-of-the-art sensing chamber. This detector is designed to afford open area protection and is for use with compatible two-wire control panels only. Once the detector senses a fire, it latches in alarm and remains in this condition until it is reset by momentary power interruption.

System Sensor Model BEAM1224 is a 4-wire conventional projected beam smoke detector. It is uniquely suited for protecting open areas with high ceilings where other methods of smoke detection are difficult to install and maintain. It is to be used with UL Listed compatible control panels only. Installation of the single-ended reflective design is much easier than the dual-ended projected beam detectors. Alignment is quickly accomplished via an optical sight and a 2-digit signal strength meter incorporated into the product. Listed for operation from –22°F to 131°F, BEAM1224 can be used in open area applications to provide early warning in environments where temperature extremes exceed the capability of other types of smoke detection.

BEAM1224 consists of a transmitter/receiver unit and a reflector. When smoke enters the area between the unit and the reflector it causes a reduction in the signal and, when the smoke level reaches the predetermined threshold, an alarm is activated.

The 2351E photoelectric smoke detector forms part of the Series 300 range of conventional detectors. This range of detectors has been produced using the latest in manufacturing and design techniques, pushing out the boundaries of existing conventional detector technology. With its multitude of innovative features, the Series 300 is a detector which ‘acts conventionally, thinks intelligently.

Key Features:

• Low profile design
• Low current draw
• Backward compatible with Series 100 detector range of bases
• Wide operating voltage 8 to 30VDC
• Bi-colour LED detector status indicator
• Automatic drift compensation
• Programmable sensitivity
• Addressable feature
• Advanced maintenance features via remote hand-held test unit
• Range of detector bases available
• Tested and approved to EN54 – 7:2000

The ZX1e is an intelligent fire alarm control panel. It has been designed and constructed around proven and reliable microprocessor technology. This simple approach has produced a modular, scaleable fire alarm platform suitable for protecting all types of premises. The ZX1e control panel supports a total of five industry leading protocols, allowing fire detection devices to be independently selected based on performance or aesthetic appeal. The ZX series control panels seamlessly integrates with Apollo (Xplorer, XP95 & Discovery), Hochiki ESP, Nittan, Morley-IAS and System Sensor detection device protocols. Designed for maximum flexibility the ZX1e control panel is supported by a complete suite of peripherals and software tools. Information on the location of fires, faults and system status can easily be displayed or printed in multiple locations. Integration to Voice Evacuation Systems, paging systems and third party control systems is supported through a range of peripheral interface units.

Features:

• Multi Protocol
• Modular concept
• Simple, robust design
• Intuitive to use
• Easy to maintain
• Easy to expand
• Easy to network
• Easy to install
• Easy to configure

The MI-STR is a low profile analogue addressable loop powered strobe designed for use with Morley-IAS protocol fire alarm control panels. This product forms part of a co-ordinated range of high quality, high performance products featuring unique styling and high efficiency. The loop-powered strobes have a very low current consumption (< 4.1mA when active). This low current allows a greater number of strobes to be powered from a single loop. The MI-STR loop powered strobe is manufactured as an analogue-addressable device with accompanying base. With the advent of the Disability Discrimination Act, the loop-powered strobe makes a useful addition to the Morley-IAS range of devices in facilitating compliance with certain aspects of the Act. The loop-powered strobe has been designed to simplify installation and includes terminals for both incoming and outgoing cables and an earth termination for cable screens. Mounting hardware and installation instructions are provided with each device.

Features:

• Loop powered

• Low-profile design
• Analogue addressable communication Low current consumption
• Wide viewing angle
• IP54 rated model
• Stable communication technique with noise immunity
• Morley-IAS Protocol

The MI-AWS addressable loop powered sounders are designed for use with Morley-IAS protocol fire alarm control panels. These products form a co-ordinated range of high quality, high performance products, featuring unique styling, simple tone selection and high efficiency. These loop powered sounders have a very low current consumption (4.1 mA at a standard volume setting). This low current means a greater number of sounders can be powered from a single loop. The sounders have been designed to simplify installation featuring large terminals for both incoming and outgoing cables. The MI-AWSR and MI-AWSW wall sounders are supplied with a surface back box allowing direct surface cable entry or direct mounting to a standard electrical box using the centre fixings.

Key Features:

• Low profile design
• Loop powered
• High sound output
• Low current consumption
• Three tones available
• High and standard volume settings
• Available in red or white
• Rotary address switches

The Dimension series of intelligent multi protocol fire alarm control panels from Morley-IAS Fire Systems have been developed based on two concepts - simplicity and reliability.

Features:

• Complies with EN54 part 2 and part 4
• 40 fire zone LED indicators
• 2 independent sounder circuits
• 500mA Loop Drivers
• 7 day timers
• Day/Night mode switching
• Onboard monitored inputs
• Programmable user function keys
• Event logging
• Onboard diagnostics
• User access restriction
• All metal enclosure
• Plug-in connectors
• Optional internal printer
• PC configuration software

The MI-D2ICMO dual input/single output modules are used with the Morley-IAS intelligent fire alarm control panels to provide a dual input circuit from external devices and a single relay control output circuit.
Each input is continuously monitored for normal, open circuit and alarm conditions. Any change in the status of the input circuits are communicated to the panel where the appropriate actions may be undertaken. A single pole volt free changeover relay is available for control of external devices or circuits.

Special Features Of The Product:

• Dual inputs
• Single relay output
• DIN rail mounting option
• Surface mounting option
• Tri-colour LED status indication
• Built-in short circuit isolators
• Visible address selector switches
• LED status visible in 2 planes
• Plug in connectors
• Approved to GEA GEI 1-082 and CEA GEI 1-084

Beam smoke detector, designed to operate as a component of an intelligent fire alarm system. It operates primarily on the principle of light obscuration utilising an Infra-Red beam. Optical beam smoke detectors are particularly appropriate for protecting buildings with large open spaces such as warehouses, atriums etc. The MI-LPB2 detector is a combined transmitter/receiver unit that can be directly connected to an analogue loop circuit. The Infra-Red transmitter generates a beam of light towards a high efficiency reflector. The reflector returns the beam to the receiver where an analysis of the received signal is made. The change in the strength of the received signal is used to determine the alarm condition. Alignment of the detector is simplified with the aid of the detector’s "gunsight" targeting device. Alignment of the detector with the reflector can then be “fine tuned” with the aid of a numerical signal strength indicator.

Features:

• Combined transmitter and receiver unit
• Range 10-100 metres
• 4 x fixed sensitivity/threshold levels
• 2 x automatic variable sensitivity modes
• Operates in the Infra-Red light spectrum
• Numerical indicators to aid beam alignment
• Standby, fault and alarm LED indicators visible from the front and bottom
• ±10° horizontal and vertical beam alignment
• Automatic drift compensation
• Loop powered
• Complies to EN54-12
• Extended Warranty